300+ câu trắc nghiệm Tiếng Anh Công nghệ ô tô có đáp án - Phần 8
Đề thi

300+ câu trắc nghiệm Tiếng Anh Công nghệ ô tô có đáp án - Phần 8

A
Admin
Đại họcTrắc nghiệm tổng hợp82 lượt thi
30 câu hỏi
1. Trắc nghiệm
• 1 điểm

Which of the following depends on the charging and discharging rate of a capacitor?

Time constant

Current

Power

Voltage

Xem đáp án

Chọn đáp án A

2. Trắc nghiệm
• 1 điểm

What is the initial current while charging a capacitor?

High

Low

0

Cannot be determined

Xem đáp án

Chọn đáp án A

3. Trắc nghiệm
• 1 điểm

What is the final current while charging a capacitor?

High

Zero

Infinity

Low

Xem đáp án

Chọn đáp án B

4. Trắc nghiệm
• 1 điểm

Capacitor is a device used to__________

Store electrical energy

Vary the resistance

Store magnetic energy

Dissipate energy

Xem đáp án

Chọn đáp án A

5. Trắc nghiệm
• 1 điểm

Capacitor stores which type of energy?

Kinetic energy

Vibrational energy

Potential energy

Heat energy

Xem đáp án

Chọn đáp án C

6. Trắc nghiệm
• 1 điểm

Capacitor blocks__________ after a long time.

Alternating current

Direct current

Both alternating and direct current

Neither alternating nor direct current

Xem đáp án

Chọn đáp án B

7. Trắc nghiệm
• 1 điểm

Which of the following is a passive device?

Transistor

Rectifier

Capacitor

Vacuum Tubes

Xem đáp án

Chọn đáp án C

8. Trắc nghiệm
• 1 điểm

For which medium is capacitance high?

Air

Mica

Water

Metal

Xem đáp án

Chọn đáp án D

9. Trắc nghiệm
• 1 điểm

Which component in the DC generator produces a magnetic field?

Stator

Commutator

Armature

Carbon brushes

Xem đáp án

Chọn đáp án D

10. Trắc nghiệm
• 1 điểm

Which component in the alternator produces a magnetic field?

Frame

Stator

Regulator

Rotor

Xem đáp án

Chọn đáp án D

11. Trắc nghiệm
• 1 điểm

At the start of the engine, the charging voltage is _______

Lower

Higher

Same

Zero

Xem đáp án

Chọn đáp án B

12. Trắc nghiệm
• 1 điểm

In an alternator, which component controls the output?

Voltage regulator

Cutout relay

Current regulator

Diode

Xem đáp án

Chọn đáp án A

13. Trắc nghiệm
• 1 điểm

What is the material of an alternator frame?

Cast iron

Brass

Copper

Aluminum

Xem đáp án

Chọn đáp án D

14. Trắc nghiệm
• 1 điểm

If the lead-acid cell has a total of 17 cells, then what is the number of positive plates?

9

8

7

6

Xem đáp án

Chọn đáp án B

15. Trắc nghiệm
• 1 điểm

Which of the following is not an advantage of the alternator?

Higher output

Lower weight

Less maintenance

High efficiency

Xem đáp án

Chọn đáp án D

16. Trắc nghiệm
• 1 điểm

Field coils in a generator produce permanent magnet.

True

False

Xem đáp án

Chọn đáp án B

17. Trắc nghiệm
• 1 điểm

What is the color of a positive plate of a lead-acid battery?

White

Grey

White

Brown

Xem đáp án

Chọn đáp án D

18. Trắc nghiệm
• 1 điểm

What gets deposited on the plates of a discharged lead-acid battery?

PbO2

Pb2O4

Pb

PbSO4

Xem đáp án

Chọn đáp án D

19. Trắc nghiệm
• 1 điểm

What is the number of positive plates in a battery cell?

One more than the negative plates

Two less than the negative plates

One less than the negative plates

Two more than the negative plates

Xem đáp án

Chọn đáp án C

20. Trắc nghiệm
• 1 điểm

What is a maintenance-free battery?

A battery having lead-antimony plate grid

A battery having lead-calcium plate grid

A battery does not contain acid

A battery does not contain water

Xem đáp án

Chọn đáp án B

21. Trắc nghiệm
• 1 điểm

Which of the following is the advantage of alkaline battery?

High energy density

Good discharge characteristics over a wide range of temperature

The specific gravity of electrolyte remains the same

Cheap raw materials are used

Xem đáp án

Chọn đáp án C

22. Trắc nghiệm
• 1 điểm

Which of the following is the best method to measure the speed?

Mechanical tachometer

Electrical tachometer

Magnetic pickup

Mechanical counters

Xem đáp án

Chọn đáp án C

23. Trắc nghiệm
• 1 điểm

The function of the ignition system is to _____________ the flame propagation process.

Stop

Initiate

Balance

None of the mentioned

Xem đáp án

Chọn đáp án B

24. Trắc nghiệm
• 1 điểm

The total enthalpy required to cause the flame to be self-sustaining and promote ignition, is given by the product of the surface area of the spherical flame and the enthalpy per unit area.

True

False

Xem đáp án

Chọn đáp án A

25. Trắc nghiệm
• 1 điểm

A spark can be caused by applying a sufficiently low voltage between two electrodes separated by a gap.

True

False

Xem đáp án

Chọn đáp án B

26. Trắc nghiệm
• 1 điểm

An ignition process obeys the law of ______________

Conservation of mass

Conservation of energy

Conservation of momentum

None of the mentioned

Xem đáp án

Chọn đáp án B

27. Trắc nghiệm
• 1 điểm

As air is a poor conductor of electricity, an air gap in an electric circuit acts as a high _____________

Conductor

Resistance

Ignition

None of the mentioned

Xem đáp án

Chọn đáp án B

28. Trắc nghiệm
• 1 điểm

An ignition system should provide a good spark between the _____________ of the plugs at the correct timing.

Cathodes

Anodes

Electrodes

None of the mentioned

Xem đáp án

Chọn đáp án C

29. Trắc nghiệm
• 1 điểm

An ignition system should be heavy, effective and reliable in service.

True

False

Xem đáp án

Chọn đáp án B

30. Trắc nghiệm
• 1 điểm

The interference from the low voltage source should not affect the functioning of the radio and television receivers inside an automobile.

True

False

Xem đáp án

Chọn đáp án B

Bạn có thích hoạt động này không?

Bắt đầu ngay
Khám phá các nguồn tài nguyên miễn phí, phù hợp với tiêu chuẩn trong vài giây
Tâm lý du khách và hành vi tiêu dùng du lịchVăn hóa ẩm thựcCAD/CAMDung sai và Kỹ thuật đoLý thuyết cơ cấuQuản lý chất lượng sản phẩmMạng truyền thông công nghiệpVi xử lý và cấu trúc máy tínhNhập môn Công nghệ ô tôTiếng anh Công nghệ ô tôNguyên lý chi tiết máyEcgonomiKỹ năng sử dụng CNTT cơ bảnNăng lượng tái tạo bền vữngNguyên lý động cơ đốt trongCông nghệ bảo trìKỹ thuật điều độMarketing B2BNgôn ngữ lập trìnhChuyên đề Kế toán trong doanh nghiệp xuất nhập khẩuKỹ năng phỏng vấnKỹ năng tổ chức và điều hành cuộc họpVận tải đa phương thứcPhát triển ứng dụng thực tại ảoLý thuyết đồ thịHệ thống thông tin vô tuyếnTích hợp hệ thống phần mềmMạng nơ-ron nhân tạoThiết kế hệ thống số dùng HDLMật mã ứng dụngPhân tích mã độc cơ bảnAn toàn và khôi phục dữ liệuĐiều khiển logicHệ thống quản lý và tự động hóa tòa nhàBảo vệ chống quá điện ápSCADAThiết bị trao đổi nhiệtVật liệu nhiệt-lạnhLò hơi và mạng nhiệtKỹ thuật sấyKỹ thuật thông gió và điều hoà không khíĐo lường nhiệtỨng dụng Revit MEP trong thiết kếThiết kế hệ thống thông gió và điều hòa không khíĐiều khiển sốSản xuất linh hoạt FMSTối ưu và quy hoạch thực nghiệmKỹ thuật xúc tácCông nghệ cao suCông nghệ gốm sứGiản đồ phaCông nghệ nanoCông nghệ xi măngCông nghệ các chất hoạt động bề mặtHóa chất bảo vệ thực vậtPhương pháp phân tích điện hóaPhương pháp sắc kýĐánh giá cảm quan thực phẩmThực hành tổng hợp hóa dầuCông nghệ chế biến dầu mỡ bôi trơnThực hành phân tích chất lượng sản phẩm xăng, kerosen và dieselPhân tích công cụQuan trắc môi trườngVi sinh thực phẩmCông nghệ chế biến đường mía và bánh kẹoCông nghệ chế biến sữa và các sản phẩm từ sữaCông nghệ đồ hộp thực phẩmCông nghệ rượu bia và nước giải khátCông nghệ sản xuất tinh dầuCông nghệ chế biến chè, cà phê, thuốc láHóa học hợp chất dị vòngQuản lý và kinh tế dượcDược động họcTác phong làm việc chuyên nghiệpHóa học vật liệu dệtAn toàn lao động trong ngành dệtDự báo xu hướng Thời trangKinh doanh và phát triển thương hiệu thời trang